User’s Guide A-61169 Part No. 3E9708 i800 Series Scanners
A-61169 July 2003 2-1 2 Using the Scanner This chapter provides the following operational procedures: • Turning on the scanner • Document prepar
2-2 A-61169 July 2003 Document preparation Kodak scanners have been tested with a range of documents that represent the broad spectrum of document
A-61169 July 2003 2-3 • For heavily damaged documents, a clear document protector can be used with the following limitations: – Manual feeding is
2-4 A-61169 July 2003 Maximum document batch height for automatic feeding When feeding batched documents, the maximum height of the batched docume
A-61169 July 2003 2-5 Adjusting the output tray Different paper types stack differently. The output tray can be set with either the front or the re
2-6 A-61169 July 2003 Scanning documents Before you scan documents, be sure the menu bar is displayed on the Operator Control Panel. Documents mu
A-61169 July 2003 2-7 Loading long documents in the feeder The feeder accommodates documents up to 76.2 cm (30 in.) in length. To feed documents lo
2-8 A-61169 July 2003 Feeding thick documents To feed thick documents: 1. Press and hold the gap release lever this provides more clearance to
A-61169 July 2003 3-1 3 Operator Control Panel Functions There are a variety of functions available from the Operator Control Panel. This chapter p
3-2 A-61169 July 2003 Enabling and disabling the scanner The five buttons at the bottom of the Control Panel correspond to the icons above the but
July 2003 1 Safety and Installation Information for the Kodak i800 Series Scanners IMPORTANT: Equipment shall be installed by qualified personnel.
A-61169 July 2003 3-3 Disabling the scanner The scanner can be disabled from the host computer or the scanner, if the end-of-job function is assign
3-4 A-61169 July 2003 Navigating through the functions on the control panel menu The left and right arrows navigate along the top of the menu bar.
A-61169 July 2003 3-5 Accessing information The information icon will display information including the last image address, meter values, and scann
3-6 A-61169 July 2003 Performing a self-test or extended self-test You can perform a self-test or an extended self-test on the scanner. The self-t
A-61169 July 2003 3-7 Performing a print test The print test checks to be sure the ink jets in the Document Printer are functioning properly. To pe
3-8 A-61169 July 2003 Performing a patch test Use this test to verify that the Patch Reader is operational and that your patches are within speci
A-61169 July 2003 3-9 Using the Settings menu The Menu icon displays the Diagnostics Settings menu. The following Settings functions are avail
3-10 A-61169 July 2003 Changing the display contrast This setting allows you to adjust the contrast of the display screen from 0 to 4. 0 = lightes
A-61169 July 2003 3-11 3. Use the down arrow to select Change SCSI ID. 4. Select Return. 5. Use the up and down arrows to select the desired SC
3-12 A-61169 July 2003 4. Select Return. 5. Use the up and down arrows to select the desired SCSI termination setting. 6. Select Return. 7.
July 2003 2 Taiwan Japan Class A This equipment is in the Class A category (Information Technology Equipment to be used in commercial and/or in
A-61169 July 2003 3-13 4. Select Return. 5. Use the down arrow to select the desired elevator position. 6. Select Return. The elevator position
3-14 A-61169 July 2003 Jogging the transport The Jog button temporarily (4 seconds) turns on the transport to help clear a document jam. This fu
A-61169 July 2003 4-1 4 Document Printer and Patch Reader This chapter provides instructions for using the Kodak Imagelink Document Printer 1 and t
4-2 A-61169 July 2003 The Document Printer can print one line per document. The information printed by the Document Printer appears in a single col
A-61169 July 2003 4-3 Horizontal print position The horizontal print position is set using one of the 13 positions in the Document Printer well. Pr
4-4 A-61169 July 2003 Purging the ink cartridge Additional ink cartridges can be purchased from an office supply retailer nearest you. NOTES: • I
A-61169 July 2003 4-5 4. Gently press the paper clip against the side of the ink bladder until a small bead of ink appears on the ink flow point on
4-6 A-61169 July 2003 3. Raise the locking bar if it is not already in the raised position and remove the empty ink cartridge. 4. Insert a new,
A-61169 July 2003 4-7 Replacing the ink blotter strips Ink blotter strips collect ink overflow. They should be replaced when there is a build-up of
4-8 A-61169 July 2003 5. Grasp a blotter strip and carefully pull it off the transport. Discard the soiled strips. 6. Install the new blotter st
A-61169 July 2003 1-1 1 Introduction This User’s Guide provides information and operator procedures for the Kodak i800 Series Scanners. The inform
A-61169 July 2003 4-9 Setting the printer position There are 13 possible positions for the printer. Make sure that the printer is in the correct pos
4-10 A-61169 July 2003 The Patch Reader The Patch Reader allows you to automatically increment the image address or initiate a special function. Pa
A-61169 July 2003 4-11 Patch Types 2, 3 and T these patch types are used for image addressing. When the Patch Reader detects a patch, it automatic
4-12 A-61169 July 2003 Setting the Patch Reader position There are 5 patch locations available for patch reading. 1. Set the documents in the elev
A-61169 July 2003 5-1 5 Maintenance This chapter provides cleaning and replacement procedures for your scanner. For best scanner performance clea
5-2 A-61169 July 2003 Cleaning the upper transport area Follow the steps below to clean the upper transport area: 1. Open the top cover. 2. Open
A-61169 July 2003 5-3 6. Place the upper imaging guide on a clean surface. NOTE: To avoid getting any debris (from the cleaning process) on the
5-4 A-61169 July 2003 10. Lift and hold the exit transport plate and vacuum. 11. Lower the exit transport plate.
A-61169 July 2003 5-5 Cleaning the vertical transport area Follow the steps below to clean the vertical transport area: 1. Grasp the vertical tran
5-6 A-61169 July 2003 6. Vacuum the floor of the lower transport area. 7. Raise the vertical transport plate into its original position. 8. Tur
1-2 A-61169 July 2003 Product description The Kodak i800 Series Scanners are ideal for operation with bi-tonal and/or color documents, documents w
A-61169 July 2003 5-7 2. Lift the roller cover and vacuum the sensors. IMPORTANT: When vacuuming the scanner, be careful not to scratch the se
5-8 A-61169 July 2003 6. Vacuum the floor of the horizontal transport area. 7. Wipe the upper and lower sensors with a lint-free cloth. 8. Rei
A-61169 July 2003 5-9 Cleaning the printer and patch head Follow the steps below to clean the Document Printer 1 and Patch Reader head. Complete in
5-10 A-61169 July 2003 Cleaning the imaging guides Avoid getting fingerprints on the imaging guides during the cleaning procedure. 1. Open the bi-
A-61169 July 2003 5-11 Maintenance and replacement procedures This section provides procedures for replacing the following parts. Use the list belo
5-12 A-61169 July 2003 Replacing the feed module and feed module tires This section provides replacement procedures for the feed module and the fee
A-61169 July 2003 5-13 Replacing the feed module tires To replace the feed module tires: 1. Open the swing out door. 2. Remove the feed module. 3
5-14 A-61169 July 2003 6. Install each new tire by gently stretching it over the core. IMPORTANT: Do not overstretch the tire; it may tear. 7. R
A-61169 July 2003 5-15 Separation roller and tires This section provides procedures for changing the separation roller and tires. Replacing the sep
5-16 A-61169 July 2003 Replacing the separation roller tires To replace the separation roller tires: 1. Remove the separation roller as previously
A-61169 July 2003 1-3 Standard configurations Four models of the Kodak i800 Series Scanners are available: • Kodak i810 Scanner (bi-tonal) provi
A-61169 July 2003 5-17 Cleaning the feed module tires and separation roller tires The cleaning procedures below should be performed daily. More fre
5-18 A-61169 July 2003 2. Grasp the green handle of the lamp connector. 3. Slightly raise the edge of the black holder and remove the lamp conne
A-61169 July 2003 5-19 5. Position the new lamp in the lamp holder. IMPORTANT: Make sure that the clear surface of the lamp is positioned facing
5-20 A-61169 July 2003 Replacing the imaging guides To replace the imaging guides: 1. Open the bi-fold door. 2. Remove the imaging guides. 3. S
A-61169 July 2003 5-21 Customizing the side guides for self-centering feeding A spacer is installed in the output tray, which allows the side guide
5-22 A-61169 July 2003 3. Use the screwdriver to release the center screw. 4. Remove the spacer and washer. 5. Take the geared spacer and plac
A-61169 July 2003 5-23 7. Turn the tray right-side up, reinstall the end stop and verify the guides move freely. 8. Replace the output tray. Chan
5-24 A-61169 July 2003 6. Take one tall (or short) side guide, position the guide and hold it in place. 7. Continue to hold the side guide in p
A-61169 July 2003 5-25 Ordering supplies The following supplies are available to properly maintain your system. Order them in the United States by
A-61169 July 2003 6-1 6 Troubleshooting/Messages This chapter provides the following: • procedures for clearing the document path, • informati
1-4 A-61169 July 2003 Scanner specifications Following are the dimensions and clearances for the Kodak i800 Series Scanners: Dimensions Height: 1
6-2 A-61169 July 2003 If there are still lodged documents: 3. Open the swing out door. 4. Lift the horizontal transport plate and remove any doc
A-61169 July 2003 6-3 10. Open the upper turn roller and remove any lodged documents. 11. Close the upper turn roller. 12. Close the top cover. Cl
6-4 A-61169 July 2003 16. Slide out the horizontal baffle plate and remove any lodged documents. 17. Slide the horizontal baffle plate back into
A-61169 July 2003 6-5 Message Listing Following is a list of messages and corrective actions you can take if one of the following messages appears
6-6 A-61169 July 2003 Message Description Message Action Check document preparation The documents are not prepared properly for scanning. See Ch
A-61169 July 2003 6-7 Message Description Message Action Feeder self test failed The self-test of the paper feeder failed. Perform a controlled p
6-8 A-61169 July 2003 Message Description Message Action Mechanical cal unsuccessful The mechanical calibration was unsuccessful. Be sure the cor
A-61169 July 2003 6-9 Message Description Message Action Print head not present An attempt was made to use the Document Printer and no print head
6-10 A-61169 July 2003 Message Description Message Action Unable to enable Check to be sure all doors are closed. If all the doors are closed, pe
A-61169 July 2003 6-11 Problem solving chart Use the chart below as a guide to check possible solutions to problems you may encounter when using th
A-61169 July 2003 1-5 External components See the illustration below for the location of the external components of the scanner. Back of scanner
6-12 A-61169 July 2003 Problem Possible Solutions Calibration has failed Make sure that: • the lamps have been on at least 10 minutes. • you
A-61169 July 2003 6-13 Problem Possible Solutions The output tray cannot be adjusted in or out Make sure the output tray is installed properly. Ro
6-14 A-61169 July 2003 Problem Possible Solutions Clean the black backer strip on the horizontal baffle plate. For procedures see Chapter 5, “Cle
EASTMAN KODAK COMPANY Commercial Imaging Rochester, New York 14650 Kodak is a trademark of Eastman Kodak Company. Printed on recycled paper. A-6
1-6 A-61169 July 2003 Environmental information and equipment disposal • The Kodak i800 Series Scanners are designed to meet worldwide environmen
Komentarze do niniejszej Instrukcji